Tamiya 1/24 Subaru Impreza wrc'99

250px-Subaru_World_Rally_Team_logo.svg by Gary Wilcox, on Flickr

The Subaru World Rally Team (SWRT) was Subaru's World Rally Championship (WRC) team. It used a distinctive blue with yellow color scheme that is a throwback to the sponsorship deal with State Express 555, a BAT cigarette brand popular in Asia. 555 logos were found on Subaru cars from 1993 to 2003. Subaru's WRC efforts date back to 1980, however, the team, in its current form, has existed since 1989, when the British firm Prodrive took over its operations, and its base moved from Japan to Banbury, England.
Subaru used the team to showcase its symmetrical all wheel drive technology It has credited the increased sales of its vehicles, especially the Subaru Impreza, with its success in the World Rally Championship, in addition to popularizing its all-wheel-drive system.

220px-David_Richards_crop by Gary Wilcox, on Flickr

Its 2008 season drivers were Petter Solberg with co-driver Phil Mills, and Chris Atkinson with co-driver Stéphane Prévot. David Richards was the team's Principal, and a founder and chairman of Prodrive. Paul Howarth was the team's operations director and team manager. He replaced David Lapworth in 2006. Richard Taylor is the team's managing director.

The team was historically an extremely strong one, competing in the WRC longer than any other manufacturer team in their current form. It has won the manufacturers' championship three times in 1995, 1996, and 1997, and the drivers' championship three times, in 1995, 2001, and 2003. The team's performance since the 2005 season, when Petter Solberg secured second position in the driver's championship, has been far lower than expected and the subject of much criticism. The team's 2006 season, one that has been described as "disappointing" by Richard Taylor, was the subject of a Discovery Channel series called Engineering the World Rally which aired in 2007. The 2007 season was little better, and called the "second season from hell" by Phil Mills. The team withdrew from WRC competition at the end of the 2008 season due to widespread economic downturn.

Although Subaru had participated in the World Rally Championship at various times since 1980, it was not until September 1989, that the Subaru World Rally Team, in its current form, was created. Subaru Tecnica International (STi) president Ryuichiro Kuze forged a partnership with the British firm Prodrive to prepare and enter the recently introduced Legacy RS in the World Rally Championship.

1980–1989
Subaru's initial forays into the World Rally Championship were with Subaru Rally Team Japan, run by Noriyuki Koseki, the founder of Subaru Tecnica International. The first Subaru car entered a world rally at the 1980 Safari Rally and since that, the team only participated in a few events per season, driving the Subaru Leone. Drivers in the early years included Ari Vatanen, Per Eklund, Shekhar Mehta, Mike Kirkland, Possum Bourne, and Harald Demuth.[2] The best result and only podium was achieved by Bourne at the 1987 Rally New Zealand by finishing third. With the start of the Prodrive effort, the teams competed in parallel, before being folded into each other.

1990–1992
Subaru entered its first Prodrive developed car, the Group A Subaru Legacy RS in the 1990 season, piloted by Finnish driver Markku Alén. Alen remained with the team through the 1991 season. His successes included 4th place in the 1990 Rally Finland, also known as the 1000 Lakes Rally, and in 1991, a 3rd and two 4th places. For the 1992 season, Subaru only entered seven of the fourteen WRC events, preferring to demonstrate the car's ability on gravel rallies. The drivers for 1992 were Finn Ari Vatanen with co-driver Bruno Berglund and Scotsman Colin McRae with co-driver Derek Ringer.[3] Both drivers were able to achieve second-place finishes. Colin McRae also won the British Rally Championship in 1991 and 1992.

1993

220px-LEGACY_RS by Gary Wilcox, on Flickr
1993 Legacy RS in 555 livery

For the 1993 World Rally Championship season, the Subaru team debuted its now distinctive blue and yellow color scheme, along with a new title sponsor, State Express 555. Ari Vatanen and Colin McRae remained the primary drivers, with the season being McRae's first complete year of World Rally Championship competition. Markku Alén, returned part-time to the team after a brief stint at Toyota in 1992, and took 4th for Subaru in Portugal.[19] McRae took the first win for Subaru, at the eighth event of the season, Rally New Zealand, the last outing for the Group A Subaru Legacy rally cars. At the next event, Rally Finland, Subaru debuted their new Prodrive developed Group A Impreza rally car, known as the Impreza 555, driven by Vatanen and Alén. Alén crashed on the first stage, and did not drive for Subaru again. Vatanen, however, showed the car to be quick, even leading the rally at one point, and managing a second-place finish. At the end of the season, Vatanen took seventh in the Drivers’ Championship, and Colin McRae finished in fifth with 50. Subaru finished third in the Manufacturers’ Championship. Other drivers also competed for the Subaru team at selected events. New Zealand driver Possum Bourne, veteran of Subaru's early days, joined the team for the Rally New Zealand and Rally Australia. Piero Liatti competed in Rallye Sanremo and Rally Great Britain. Drivers Richard Burns and Alister McRae had competed in the British Championship, which Burns won, and appeared again in Legacies for Rally Great Britain, where Burns finished seventh and McRae tenth. Drivers Per Eklund and Hannu Mikkola drove for the team in Rally Sweden.

1994–1995
In 1994, former World Rally Drivers' Champion Carlos Sainz joined the team with co-driver Luis Moya, and took the Impreza 555 to its first win at the Acropolis Rally in Greece. It later took wins in New Zealand and Great Britain with McRae at the wheel. In the Championship for Manufacturers, they achieved a second-place finish, behind Toyota, with Sainz placing second in the driver's championship, and McRae placing fourth. Other drivers for the Subaru team in 1994 included Patrick Njiru, competing in the Safari Rally, Richard Burns in the Safari Rally and Rally Great Britain, Possum Bourne in New Zealand, and Piero Liatti at Rallye Sanremo.

For the 1995 season, the primary drivers remained Sainz in the number 5 car and McRae in the number 4 car. Sainz won the season opening round at the Rallye Monte Carlo, while McRae crashed out of the event. At Rally Sweden, Sainz, McRae, and third driver Mats Jonsson all retired with engine trouble. Sainz won again at the Rally Portugal, while McRae finished in third place. At the Rallye de France, Sainz, McRae, and third driver Piero Liatti finished in the fourth, fifth, and sixth places respectively. At Rally New Zealand, McRae took his first win of the season. Other drivers for the team included Possum Bourne, who finished in seventh place, and Richard Burns who retired with a mechanical failure. At the Rally Australia, McRae took second place. Sainz retired after his radiator failed, while third driver Bourne retired after an accident. At the Rallye Catalunya, Subaru locked out the podium with a 1–2–3 finish. Sainz took first, McRae took second, and third driver Piero Liatti finished third. Sainz's first-place finish in Catalunya left he and McRae tied for points going into the last event of the season, the RAC Rally of Great Britain. McRae won out, taking first place at his home event, clinching his first and only Driver's Championship, a first for the Subaru team. Sainz finished close behind in second place, giving him second in the Championship, and third driver Richard Burns finished in third place, giving the team a second consecutive 1–2–3 finish. Between McRae and Sainz the team managed to win five of the season's eight rallies for Subaru, winning the team its first Constructors Championship. At the end of the season, Sainz left Subaru to join Ford World Rallye Sport.

1996

220px-Colin_McRae_Subaru_Impreza_WRC by Gary Wilcox, on Flickr
Colin McRae's 1996 Impreza 555

For the 1996 World Rally Championship season, Colin McRae was again the lead driver for Subaru. Following his 1995 Championship victory, his Impreza 555 wore the #1 plate. He was joined by team drivers Kenneth Eriksson, in the #2 car, and Piero Liatti, with their co-drivers, Staffan Parmander and Mario Ferfoglia, respectively. At the first event of the season, Rally Sweden, McRae took third, Eriksson took fifth, and Liatti took twelfth. 1994 World Drivers' Champion Didier Auriol also drove for the Subaru team in Sweden, taking his #3 car to tenth place. At the second round, the Safari Rally, Liatti's number was changed from #10 to #3. He took fifth place. McRae took fourth while Eriksson took second. At the Rally Indonesia, Liatti finished in second place, while McRae and Eriksson both retired following accidents. McRae's first victory of the season was at the Acropolis Rally, the fourth round of the championship. Liatti and Erikkson placed fourth and fifth respectively. Eriksson took third and Liatti fifth at Rally Argentina. McRae crashed out of Rally Argentina and the following event, Rally Finland. Liatti didn't compete in Finland, though Eriksson managed to finish in 5th place. McRae, Eriksson, and Liatti finished 4th, 2nd, and 7th respectively at Rally Australia. In Sanremo, McRae took victory, with Eriksson finishing in 5th. Liatti retired following an electrical failure. At the last round of the season, Rallye Catalunya, McRae took a second consecutive victory. Subaru took a 1–2 finish with Liatti finishing second. Eriksson finished in seventh position. Thanks to consistent podium finishes, Subaru successfully defended its Constructors' Championship, but McRae lost the Driver's Championship to Tommi Makinen.

1997–1998
For 1997, McRae again led the team, however his co-driver Derek Ringer was replaced by Welshman Nicky Grist. Secondary driver/co-driver teams included Piero Liatti/Fabrizia Pons (first in Monte Carlo), Olivier Burri/Christophe Hofmann and Kenneth Eriksson/Staffan Parmander (first in Sweden and New Zealand). Once again the team successfully defended its Constructors Championship, winning eight victories out of the fourteen rallies, but McRae again lost the Driver's Championship to Tommi Makinen, this time by just one point.

In 1998 the team had an almost unchanged line-up, although Jahu Kangas/Pentti Kuukkala and Jarno Kytölehto/Arto Kapanen participated in one round each. McRae took wins in Portugal, Corsica and Greece. However, bad weather and mechanical failures hurt the team, and Subaru and McRae finished third in their respective championships. At the end of the season, McRae left the team to join Ford, with the tantalizing prospect of driving their brand-new car, the Ford Focus WRC.

1999–2001

220px-Petter_Solberg_-_2006_Cyprus_Rally_5 by Gary Wilcox, on Flickr
Petter Solberg

Subaru had an all new line up for the 1999 season, with the nominated driver/co-driver teams of Richard Burns/Robert Reid, Juha Kankkunen/Juha Repo, and third team of Bruno Thiry/Stéphane Prévot. The new car, the WRC99, featured an electronically controlled Paddle shifter with a drive-by-wire throttle. Due to technical difficulties, the team struggled until the season's 7th round in Argentina. From there on, the teams earned the podium in seven out of eight events, with five wins, three of which were 1–2 finishes. Subaru finished second in the Manufacturers’ Championship, just four points behind Toyota. Burns scored victories in Greece, Australia, and Wales, for second place and Kankkunen took fourth in the Drivers’ Championship, with wins in Argentina and Finland.

Burns and Kankkunen continued to drive for Subaru for the 2000 season, with Petter Solberg joining the team halfway through the season, driving in the Rallye de France. The team finished third in the championship, and Burns took second in the Drivers' Championship for the second year in a row.
Burns and Solberg composed Subaru's nominated line-up for the 2001 season with Markko Märtin/Michael Park and Toshi Arai/Tony Sircombe competing in selected events. Subaru again won the Driver's Championships in 2001 with Richard Burns and co-driver Robert Reid. Burns left Subaru for Peugeot at the end of the 2001 season.

2002–2003

220px-Wrc_fin_2004_makinen by Gary Wilcox, on Flickr
Tommi Mäkinen

For the 2002 season, Burns was replaced by Tommi Mäkinen and co-driver Kaj Lindström. Petter Solberg continued with the team, and Pasi Hagstrom was the team's test driver. Following the October 2001 signing of four time driver's Championship winner Mäkinen, expectations for the team ran high. However, after a season opening win in Monte Carlo, he was only able to finish five more events during the entire season. His teammate, Solberg fared much better, finishing nine events, five of which were podium finishes, including his first ever WRC win, at Rally Great Britain, the season's last round. The win propelled him past Ford's Carlos Sainz into second in the Drivers' Championship.

For the 2003 season, the driver line-up remained unchanged from the previous year. Solberg drove the #7 car, Mäkinen the #8 car. The season got off to a poor start, with neither driver finishing the Rallye Monte Carlo. Solberg then scored four outright wins, in Cyprus, Australia, France, and finished the season with his second straight win in Britain, securing him the Driver's Championship for himself and co-driver Phil Mills, narrowly beating Sébastien Loeb by one point. The team only managed to achieve third place in the manufacturers' championship, beaten by Citroen and Peugeot. At the end of the season, Tommi Mäkinen retired from the WRC.

2004–2005

220px-Petter_Solberg_-_2005_Cyprus_Rally by Gary Wilcox, on Flickr
Subaru Impreza WRC2005 being driven by Petter Solberg at the Cyprus Rally

For the 2004 season, Solberg was joined by Finnish driver Mikko Hirvonen and his co-driver Jarmo Lehtinen. Subaru managed to consolidate third place in the Manufacturer's Championship again, while Solberg was second in the Driver's Championship, winning five of the season's rallies: New Zealand, Greece, Japan, Italy and a third consecutive win at Rally Wales. Hirvonen ended the season in seventh place, failing to impress the Subaru team management. He was not re-signed for the 2005 season.
In 2005, Petter Solberg again led the team in the #5 car, while Hirvonen was replaced by Chris Atkinson in the #6 car. The young Australian debuted with the Uddeholm Swedish Rally, and finished third at Rally Japan. Petter Solberg achieved back-to-back victories in Mexico and Sweden, early in the season. He finished the season behind Sébastien Loeb, tied for second place with Marcus Grönholm. In the Manufacturer's championship, Subaru only managed to finish fourth overall, ahead of Mitsubishi and Skoda.

2006

220px-Chris_Atkinson_2006_Rally_Cyprus by Gary Wilcox, on Flickr
Chris Atkinson

Petter Solberg again led the team throughout the 2006 season, with the second car piloted by Chris Atkinson and co-driver Glenn MacNeall on gravel events, while on tarmac events, it was driven by ex-Formula One driver Stéphane Sarrazin. The WRC2006 had several changes from the previous year's car due to rule changes which banned active differentials as well as water injection, as well as mandating that teams must re-use cars and engines on selected ‘pairs’ of events. Due to the rule changes, the car was introduced on the first round of the season.

Subaru's season got off to a poor start, with Solberg unable to score in the first two rallies due to mechanical failures.[70] Due to the teams lacklustre performance, after a decade of running the team, team boss David Lapworth was replaced by Paul Howarth. Not until the third rally of the season, Rally Mexico, would Petter manage to score, achieving a second-place finish. He picked up another second-place finish at Rally Argentina, and again at Rally Australia. The team finished the season in third place in the manufacturer's championship, while Solberg finished in sixth place in the driver's championship. However, the team was not able to achieve a single win, and achieved podium results only four times. Subaru's 2006 season was characterized as disappointing, and was the subject of a Discovery Channel series called Engineering the World Rally.[8][11][12][13] In the programme, Subaru's dismal season was described as 'The Season from Hell'.

2007

220px-Petter_Solberg-2007_Wales_Rally_GB_002 by Gary Wilcox, on Flickr
Solberg's WRC2007 at Rally GB

Solberg again led the team for the 2007 season, driving the #7 Impreza. Sarrazin left the team, leaving Chris Atkinson as the single number two driver, piloting the #8 car. Atkinson managed to grab fourth place at the season opening event in Monte Carlo, after passing the works Ford of Mikko Hirvonen. At the 2007 Rally Portugal, Solberg came in second, following the Ford cars' disqualification due to the glass in their rear windows being too thin. Following the rally, Atkinson's co-driver, Glenn MacNeall, elected to leave the team, and was replaced by Stéphane Prévot, who had previously been with the team as co-driver for Bruno Thiry. At the 2007 Acropolis Rally Solberg managed to achieve a podium position.

After the summer break, the team was joined at the 2007 Rally Finland by Xavier Pons and co-driver Xavier Amigo, driving a third car, #25, not nominated for manufacturer points. However, in the rally, Solberg had to retire on day two, after monstrous handling and steering problems which the team engineers were unable to deal with. Solberg finished fifth in Ireland, calling it "the most difficult rally he has ever done." At the final event of the season, Wales Rally GB, Solberg won the battle for fourth with Dani Sordo, propelling Subaru to third place in the manufacturer's standings. In the driver's championship, Solberg came in 5th, while Atkinson took 7th. Richard Taylor called the season a "poor" one, with Subaru only achieving two podium finishes, and no overall wins for the second year in a row. Phil Mills called it the "second season from hell."

2008
Petter Solberg and Chris Atkinson continued with the team through the 2008 season. Xavier Pons left the team, although there is a possibility that he will return. With the FIA mandated switch to Pirelli tires, tyre moussehad been banned, and fewer compounds were available.

At the first rally of the season, the 2008 Monte Carlo Rally, Atkinson scored his first podium finish on tarmac, after a close battle with François Duval while Solberg finished in fifth. In the 2008 Swedish Rally, Solberg finished in fourth place while Atkinson finished in 21st position following a spin on Special Stage 3, which cost him over 15 minutes. Immediately after the Swedish Rally, the team completed a gravel test in Spain, in preparation for Rally Mexico, the last test using the WRC2007 car. At the 2008 Rally Mexico, Atkinson placed second, his best ever result. Solberg was forced to retire on the second day after a driveshaft failure to his front left wheel. He continued under SupeRally rules on Sunday, finishing 12th. Going into the final day of the 2008 Rally Argentina, Solberg and Atkinson were comfortably in second and third position, poised to put two cars on the podium, a feat Subaru has not accomplished in several years. However, on Special Stage 19, Petter's car suffered an electrical failure, forcing him to retire. Atkinson inherited Solberg's position, and achieved a second-place finish for the second consecutive time. At the 2008 Jordan Rally, on SS6, Solberg's retired after his Impreza suffered from a damper failure, which then spilled oil, lighting a fire under the hood of the car. Solberg restarted under SupeRally rules on Saturday, but crashed on the day's final stage after brake problems. Atkinson managed to secure a third podium in a row, following the suspension failure of Latvala, and the retirements of Solberg and Loeb.

Withdrawal from WRC
On 16 December 2008, it was announced that Subaru would no longer be competing in the World Rally Championships. The decision was taken by Subaru’s parent company, Fuji Heavy Industries (FHI), partly as a result of the economic downturn but also because it was felt Subaru had achieved its sporting and marketing objectives. Ikuo Mori denied that alterations to the WRC technical regulations in 2010 or a rumoured deterioration in the working relationship with Prodrive had any impact on the decision. He also said that the possibility of a Subaru car back in the top category of WRC in the future is not zero, but for this moment there can be no assumption of a comeback.

Vehicle development
Group A Leone, 1980–1989
As Subaru Rally Team Japan, Subaru entered the first World Rally with the second generation Group A Subaru Leone DL at the 1980 Safari Rally. In 1984 the model was changed to the 3rd generation Leone coupé, one year later installed with a turbo. The other model used simultaneously with the coupé turbo until 1989 was the Leone sedan RX Turbo.
Group A Legacy RS, 1989–1993

Prodrive's vehicle development began upon the team's formation in September 1989, creating the Group A Subaru Legacy RS rally car, based on the road going Subaru Legacy sedan. The Legacy was powered by a longitudinally mounted boxer engine, giving it a low centre of gravity. Already equipped with a symmetrical all wheel drive system, it made a good starting point for a rally car. David Lapworth described the development of the car as a "steep learning curve." The car lacked power and a weak transmission and braking system also hampered the car. To correct its flaws, Prodrive completed a new car, the 1992 Legacy RS, which featured a totally redesigned fuel injection system, during the 1991 season, introduced on the season's last rally. The team campaigned the 1992 Legacy during the first part of the 1993 season, and on its last rally, achieved the car's first and only win.

Group A Impreza GC, 1993–1996

220px-Colin_McRae's_Subaru_Impreza_555_crop by Gary Wilcox, on Flickr
Colin McRae's 1995 Group A Impreza 555

For 1993, Prodrive recognized that a smaller, nimbler car would make a better platform for a rally car, and work on a Group A Impreza rally car began. It was 160 mm shorter in overall length with a 60 mm shorter wheelbase, as well as having a more neutral front/rear weight ratio. It also featured active differentials, a first for a rally car. At the 1000 Lakes Rally, Subaru debuted their new Prodrive developed Impreza derived Group A rally car, driven by Vatanen and Alén. Vatanen drove the car to second place on its debut.
In 1994, the Subaru team switched from Michelin to Pirelli tires.
For the 1995 season, the FIA mandated more restrictive air intakes in an effort to slow the cars down. Subaru countered this by introducing a new boxer engine with revised camshafts and a different compression ratio.

World Rally Car Impreza GC, 1997–2001

220px-Subaru_Impreza_WRX_STI_1997_WRC_Rally_Car by Gary Wilcox, on Flickr
The first Prodrive WRC Car from 1997

For 1997, the FIA replaced the Group A formula with a new formula called World Rally Car. This gave teams greater latitude in design and materials including vehicle width, suspension geometry, aerodynamics, intercooler capacity and engine modifications. This led to a totally redesigned car, the WRC97, featuring modified camshafts, cylinder ports and combustion chambers. The new body had two doors. The width of the car increased to 1,770 mm (69.9 in) with a revised suspension geometry. Power increased to 300 hp @ 5500 rpm, and torque was now 347 lb ft.
The Impreza WRC98 was an evolution of the earlier WRC97, with computer controlled active differentials in the front, rear, and centre, and an electronic throttle. Mechanical failures were common and took the team out of contention for the title.

The WRC99, introduced at the first round of the championship, featured an electronically controlled, hydraulically actuated semi-automatic transmission with a drive-by-wire throttle, allowing the cars to be shifted with steering wheel mounted paddles, similar to F1 cars. This allowed the driver to shift gears faster, and reduced the chance of dog gear wear. Due to technical difficulties, the team struggled until the season's 7th round in Argentina. However, the car helped prove much of the technology seen on later cars. Subaru was the first rally team to implement this technology, which has been used on all WRC cars until it was forbidden by the 2011 championship rules.

Although the WRC2000 looked almost identical to the WRC99, underneath the sheet metal, its execution was radically different. Developed by Prodrive engineer Christian Loriaux, the team used the lessons learned from the WRC99 and applied them in the WRC2000's 10-month development, in which over 80% of the car's mechanical and electronic components were redesigned. The car debuted, and drove to victory, at the fourth event of the season, Rally Portugal.

World Rally Car Impreza GD, 2001–2008

220px-Ss1_5rb by Gary Wilcox, on Flickr
WRC2001

The WRC2001 featured an entirely new look, based on the GD chassis Impreza WRX. The new body had four doors (instead of two), and featured revised aerodynamics, improved weight distribution, and a lower centre of gravity. However, all the mechanical development from the previous year, including the engine, suspension, and drivetrain remained, with subtle refinements.

The WRC2002 was introduced at Corsica, and looked largely the same as the previous year's car. However, development of the car continued throughout the season. Improvements were made to the driveshaft, transmission housing, and steering column, as well as to the turbo-charger and manifold, which was changed from a 4–2–1 configuration to a 4–1 configuration. Savings found in modified brackets, wiring, and glass reduced weight by 33 lbs.

The WRC2003 was introduced at the 2003 Rallye Monte Carlo. It featured a revised look based on the updated Impreza introduced the previous year. Technical improvements were made to the turbocharger and engine, aiming to increase torque at lower RPMs allowing greater driveability. The car's body shell was made both lighter and stiffer. Throughout the year modifications were made to the car's suspension.

The WRC2004 did not feature many cosmetic changes from the previous year's car, but did have refinements in the engine and body panels. It was introduced at Rally Mexico. A revised gearbox was introduced halfway through the season.

The WRC2005 was introduced following 12 months of joint development by Subaru and Prodrive, on 11 March 2005 at Rally Mexico. Its re-styled bodyshell was stiffer, and 30 mm wider to allow a wider track. The car featured more composite body panels, including front and rear wheel arches and bumpers in order to decrease weight. Engine enhancements included a lightened flywheel and revised IHI turbocharger. Revised water injection and fuel injection systems were also introduced.
The WRC2006 had several changes from the previous year's car due to rule changes which banned active differentials as well as water injection, as well as mandating that teams must re-use cars and engines on selected ‘pairs’ of events. Due to the rule changes, the car was introduced on the first round of the season.

220px-MEX_2008_RB_05_service by Gary Wilcox, on Flickr
Solberg's WRC2007 in service at the 2008 Rally Mexico

The WRC2007, a revised version of the earlier year's car, was introduced at the fourth round of the championship, Rally Mexico. It featured new dampers, a different radiator and intercooler arrangement, as well as improved weight distribution, suspension geometry and differential set-ups. It was considered to be underachieving compared to the newly introduced 2007 Focus WRC and the all-new Citroen C4 WRC. The car suffered from extensive handling problems, resulting in Subaru withdrawing from Rally Finland on the second day of the rally.

Each transmission in the WRC2007 takes 85 hours build, and costs over ₤75,000. The front and rear differentials are similar while the centre differential is unique. Each takes around 16 hours to build costs about ₤20,000.The cases for the transmission and differentials are constructed from magnesium to reduce weight. Filled with oil, the transmission weighs 95 kg, and a differential weighs 25 kg. The car's engine, transmission and differential are individually oil sealed, so that they can be removed and replaced without fluid loss. This also helps the team replace the components in 10–12 minutes. The transmission's lubrication system has a 4.5 litre capacity and includes an oil pump to help control differential temperatures, which usually operate around 100C. The transmission retains the roadgoing Impreza's H pattern but utilizes a hydraulically actuated and electronically controlled semi-automatic gearshift.The hydraulic gear shift system operates at a pressure of 2,500psi, allowing gear shifts to be completed in less than .1 seconds.

World Rally Car Impreza GE, 2008
In December 2007, Subaru began testing the WRC2008, based on the all new GE chassis Impreza WRX.[118] The 2008 car is expected to benefit from a decreased polar moment of inertia due to smaller overhangs, and also features a double wishbone rear suspension. However, Prodrive found this setup inferior, and converted the rear suspension back to the original MacPherson design. However, an updated 2007 car will be used for the first few rallies, with the 2008 car introduced after that. Markko Märtin signed a deal to become the official test driver for the Subaru team in 2008, and has thus far done the majority of the testing on the WRC2008. During a 4-day test at Sardinia between 30 April and 3 May 2008, Petter Solberg and Chris Atkinson drove the WRC2008 for the first time. A date for its debut was still not given. On 20 May 2008, the Subaru World Rally Team confirmed its new Impreza World Rally Car (WRC2008) will make its WRC debut at the Acropolis Rally of Greece, beginning on the 29th of May. On the cars rally debut, the WRC2008 scored its first podium finish with Petter Solberg placing 2nd in the Acropolis Rally.

Post by **Rallychef** » Tue Jan 02, 2018 1:10 pm

Will be watching this one with interest, I have this car in the stash and was also lucky enough to be the Test and Development team's chef throughout the 90's & into the 2000's, so know this car well, and have very fond memories of my time with them (I just wish I knew I was going to build models in those days, I would have had some great reference photos. Are you building Richard or Bruno's car ?

Regards Ian D

Post by **Paul** » Tue Jan 02, 2018 1:15 pm

Its a great kit, filing the front lower light sections is a bit tricky to do but easy enough

Post by **gaz45** » Tue Jan 02, 2018 3:57 pm

I'll be doing the Bruno one mate.

Thanks for the tip Paul

Post by **Twokidsnosleep** » Thu Jan 04, 2018 3:14 am

Setting up for a great build thread

Looking forward to see it progress

Post by **DrSprue** » Thu Jan 04, 2018 2:12 pm

Looks like a great kit! Well done presentation as well!

Post by **Rallychef** » Thu Jan 04, 2018 3:04 pm

Here are a couple of photo's from back in the day, UK test in June 1999, with new test driver Robbie Head (and my son!) Robbie was so new in the job he hadn't even got measured up for his new overalls, hence the duct tape covering the old sponsors. And also my al fresco restaurant (hospitality suites have come on some way since the '90's

I just whish I had more reference photo's, as I say didn't know I would be building models at that time. Sorry for the poor quality pics,pre digi camera days !

Regards Ian D

Post by **gaz45** » Fri Jan 05, 2018 3:22 pm

Thanks guys

Post by **gaz45** » Fri Jan 05, 2018 3:23 pm

Rallychef wrote: Thu Jan 04, 2018 3:04 pm Here are a couple of photo's from back in the day, UK test in June 1999, with new test driver Robbie Head (and my son!) Robbie was so new in the job he hadn't even got measured up for his new overalls, hence the duct tape covering the old sponsors. And also my al fresco restaurant (hospitality suites have come on some way since the '90's

I just whish I had more reference photo's, as I say didn't know I would be building models at that time. Sorry for the poor quality pics,pre digi camera days !

Regards Ian D

Thanks for the shots mate

Post by **gaz45** » Fri Jan 05, 2018 3:55 pm

So here we go
Starting with the chassis and the drive chain these will be cleaned up ready for priming and painting it will be easier to paint most of these parts prior to building them up, as there is some detail painting to be done.

They are now cleaned up and test fitted you can't see too much until they have been painted up

20180102_134537 by Gary Wilcox, on Flickr

20180102_134631 by Gary Wilcox, on Flickr

I have decided to make up the front discs and suspension struts so these can be primed at the same time

20180102_140804 by Gary Wilcox, on Flickr

20180102_141045 by Gary Wilcox, on Flickr

These parts have now been primed with the Ultimate gloss primer

20180103_112733 by Gary Wilcox, on Flickr

20180103_112745 by Gary Wilcox, on Flickr

Some of these parts require to be painted up in semi gloss black but these i will leave as much has possible in the gloss primer.

The main body and chassis color for this i have zeropaints world rally blue subaru - 02c.

When i sprayed this over the gloss black primer i feel it looks on the dark side so for the body i think i'll use white primer but i'm open to suggestions.

20180103_143058 by Gary Wilcox, on Flickr

20180103_143113_HDR by Gary Wilcox, on Flickr

20180103_143118 by Gary Wilcox, on Flickr

For a curb side kit there is a lot of detail painting on the underside.
These parts have now been painted up some sprayed and the rest brush painted.

Here i thought it would be easier to list the paints used.

Tamiya XF-1 flat black
Tamiya X-18 semi gloss black
AK Xtreme metal polished aluminum
Tamiya XF-23 light blue
Tamiya XF-2 flat white
AK Xtreme metal chrome
Tamiya X-31 + X-32 50/50 mix
Tamiys XF-56 metallic grey
Tamiya X-10 gun metal
Tamiya X-4 blue

This is the outcome

20180105_143922 by Gary Wilcox, on Flickr

20180105_143934_HDR by Gary Wilcox, on Flickr

20180105_143943 by Gary Wilcox, on Flickr

20180105_143955 by Gary Wilcox, on Flickr

20180105_144200 by Gary Wilcox, on Flickr

20180105_144213 by Gary Wilcox, on Flickr

So that's where i'm at thanks for taking a look and for your comments and help.

Post by **exmoor** » Fri Jan 05, 2018 5:21 pm

Looking good gaz has for the primer I think I would go for white but I have seen silver being used .can't remember what Paul of ism used.

Post by **pourquoi61** » Fri Jan 05, 2018 9:39 pm

I do like a nice out of the box build, with family history to add a little interest.

Post by **Rallychef** » Fri Jan 05, 2018 9:42 pm

That is a cracking start Gaz looking forward to seeing more

Cheers Ian D

Post by **gaz45** » Sat Jan 06, 2018 11:16 am

Cheers guys

Post by **gaz45** » Tue Jan 09, 2018 3:44 pm

So now it's time to fit these parts together hoping they still fit as well now they have been painted.
For this i will use CA glue instead of the usual TET.
So far so good everything sill fits.

20180105_174517_HDR by Gary Wilcox, on Flickr

20180105_174536_HDR by Gary Wilcox, on Flickr

20180105_180220_HDR by Gary Wilcox, on Flickr

20180105_180234_HDR by Gary Wilcox, on Flickr

20180105_180421 by Gary Wilcox, on Flickr

The front wheels still turn bonus

20180105_180248 by Gary Wilcox, on Flickr

20180105_180257 by Gary Wilcox, on Flickr

20180105_180313 by Gary Wilcox, on Flickr

20180105_180322 by Gary Wilcox, on Flickr

20180105_180334_HDR by Gary Wilcox, on Flickr

While that sets up it's time to work on the rear discs, struts, drive train ans lower arms.
After looking at the instructions there is a little more detail painting on these than the front discs so these will be painted before assembling this time.

20180105_182347 by Gary Wilcox, on Flickr

20180105_183640 by Gary Wilcox, on Flickr

Once again a test fit. The clear part needs to detail painted as well so this will require some masking

20180105_183614_HDR by Gary Wilcox, on Flickr

20180105_185137 by Gary Wilcox, on Flickr

To add a little more detail I have drilled out the exhaust using a pin vice and a 1.5mm drill bit

20180105_190658 by Gary Wilcox, on Flickr

20180105_185534 by Gary Wilcox, on Flickr

The colour call out for the exhaust is white which didn't seam right to me and after talking to Paul i'll be doing it in a steel colour.

I have also cleaned up some of the interior parts and again test fitted.

20180106_155443 by Gary Wilcox, on Flickr

20180106_161545_HDR by Gary Wilcox, on Flickr

20180106_161550 by Gary Wilcox, on Flickr

20180106_161601_HDR by Gary Wilcox, on Flickr

There are a couple of these parts that need to be painted in the body colour blue so to keep the interior and the chassis the same i'll use the Ultimate gloss black primer, When it comes to the actual body shell i will use the white primer.

These parts have all been primed now they will then get painted and any decals applied.

20180109_123302 by Gary Wilcox, on Flickr

20180109_123441 by Gary Wilcox, on Flickr

The paints used in this section are:- Zeropaints world rally blue, AK Xtreme metal polished aluminiun and stainless steel. The rest are Tamiya X-7 red, X-1 black, XF-56 metallic grey,X-3 royal blue, X-27 clear red, X-11 chrome silver, X-12 gold leaf, X-8 lemon yellow. XF-1 flat black, X-18 semi gloss black, XF-16 flat aluminium, X-10 gun metal and X-14 sky.blue.

While these are drying I have trimmed the aluminium sticker and put it in place.

20180109_123226_HDR by Gary Wilcox, on Flickr

Now that everything is dry time to fit them again using CA glue

20180109_130230 by Gary Wilcox, on Flickr

20180109_130249_HDR by Gary Wilcox, on Flickr

20180109_130302_HDR by Gary Wilcox, on Flickr

20180109_134733_HDR by Gary Wilcox, on Flickr

20180109_134803 by Gary Wilcox, on Flickr

20180109_134816 by Gary Wilcox, on Flickr

20180109_134832 by Gary Wilcox, on Flickr

That is all for now thanks for taking a look and for all your comments.

Post by **exmoor** » Tue Jan 09, 2018 6:51 pm

Looking awsome as always very nice

Post by **DrSprue** » Tue Jan 09, 2018 9:05 pm

Man it really is starting to look awesome!

Post by **Rallychef** » Tue Jan 09, 2018 10:30 pm

Really good progress there, liking this a lot

YouTube · Post by **OlaHansson** » Wed Jan 10, 2018 9:49 am

Looks really nice!!

Post by **Twokidsnosleep** » Thu Jan 11, 2018 2:39 am

Chanterelles, I believe those are indeed Chanterelles...must be a bit humid in those Soobie cabins

Some great car building going on here

YouTube · Post by **NorthernModeller** » Fri Jan 12, 2018 2:02 pm

Building the same kit at the minute, awesome kit and I am looking forward to seeing what you do with it

Post by **gaz45** » Tue Jan 16, 2018 1:57 pm

Cheers guys

Post by **Tomcat64** » Wed Jan 17, 2018 5:20 pm

Just catching up on some builds and that's a great intro to this thread Gaz!

The build's not too shabby either

Love the detailing inside the cabin.

Post by **pourquoi61** » Wed Jan 17, 2018 10:51 pm

Another nice Subaru underway and looking great sir.
Catching up with the build.

Post by **gaz45** » Thu Jan 18, 2018 9:36 am

Thanks guys

Post by **gaz45** » Thu Jan 18, 2018 10:02 am

Just a short update

This section i will deal with the seats and the dashboard. For the seats even though there is a carbon fibre decal to go on the backs there are some EMP's to be filled for this i will use vallejo plastic putty and when dry it will be sanded flush.

20180109_160718 by Gary Wilcox, on Flickr

20180109_160730 by Gary Wilcox, on Flickr

20180109_161406 by Gary Wilcox, on Flickr

20180109_162751 by Gary Wilcox, on Flickr

20180109_164851 by Gary Wilcox, on Flickr

At the same time i have decided to paint the wheel rims

20180109_171550 by Gary Wilcox, on Flickr

These have all been primed in the gloss black primer except for the dashboard where i used the flat black primer.

20180110_235731 by Gary Wilcox, on Flickr

These parts have now been painted and the decals on the dash have been added

For the rims i used AK Xtreme metal gold

20180118_084236 by Gary Wilcox, on Flickr

For the other parts i used Zero paints world rally blue, Tamiya XF-53 neutral grey, X-18 semi gloss black, XF-1 flat black, XF-19 sky grey, X-7 red, X-2 white, X-1 black and XF-63 german grey.
The seats were left in the gloss black primer until the decals were added then they will be given a flat clear coat as they are shown in flat black.

On some of the decals i added some kristal klear to them to depict the dial glass i'm not sure this shows up well.

20180118_084156 by Gary Wilcox, on Flickr

20180118_084130 by Gary Wilcox, on Flickr

20180118_084120 by Gary Wilcox, on Flickr

20180118_084040 by Gary Wilcox, on Flickr

20180118_084026 by Gary Wilcox, on Flickr

While they were drying and setting up I moved onto the rest of the interior parts and the rest of the roll cage,
While i was cleaning up the roll cage i noticed that the rear view mirror is attached to this and not in the usual place on the clear parts so i've added this before priming with the gloss black primer.

20180117_220926 by Gary Wilcox, on Flickr

20180118_084328 by Gary Wilcox, on Flickr

That is all for now thanks for taking a look and for all your comments.

Post by **DrSprue** » Thu Jan 18, 2018 2:29 pm

Wow the dash and seat detail looks really nice!

Post by **pourquoi61** » Thu Jan 18, 2018 9:21 pm

First class sir and those Zero paints look great.

Post by **demarcation** » Fri Jan 19, 2018 9:42 pm

Great work so far mate, fantastic attention to detail!!

Post by **gaz45** » Wed Jan 24, 2018 11:26 am

Thanks guys

Post by **gaz45** » Wed Jan 24, 2018 1:56 pm

This section is just a small update and a test for the bodywork has I will be trying a couple of new products I have never used before these are Alclad II aqua gloss and Zeropaints polishing compound set.

The update

The rest of the interior parts have been painted up using
Zeropaints world rally blue, Tamiya XF-66 light grey, XF-53 neutral grey, X-11 chrome silver, XF-19 sky grey, XF-63 german grey and X-18 semi gloss black.

20180123_233616 by Gary Wilcox, on Flickr

20180123_233612 by Gary Wilcox, on Flickr

Now all these are dry i will add them to the chassis along with the wheels and tyres.

20180123_235218 by Gary Wilcox, on Flickr

20180123_235554_HDR by Gary Wilcox, on Flickr

20180123_235607 by Gary Wilcox, on Flickr

20180124_002223 by Gary Wilcox, on Flickr

20180124_002237_HDR by Gary Wilcox, on Flickr

20180124_002304 by Gary Wilcox, on Flickr

20180124_002316 by Gary Wilcox, on Flickr

20180124_002331 by Gary Wilcox, on Flickr

That's where the build stands for now

Right now to see what i plan to use on the bodywork

Firstly a coat of Ultimate white primer and once dry a gentle sanding with the Ultimate sponge sander

20180118_113723 by Gary Wilcox, on Flickr

Then painted in the Zeropaints world rally blue and left to dry

20180119_124947 by Gary Wilcox, on Flickr

When that was dried I added some spare decals and when they were set I clear coated this with the Alclad II aqua gloss

20180123_232430 by Gary Wilcox, on Flickr

20180123_232436 by Gary Wilcox, on Flickr

20180123_232449 by Gary Wilcox, on Flickr

This alone gave it a good shiny finish.

After about 24 hours I have polished up half the wing with the 3 zeropaints polishing compounds.

I'm not sure if these pics show the finish too well.

20180124_123620 by Gary Wilcox, on Flickr

20180124_123616 by Gary Wilcox, on Flickr

20180124_123552 by Gary Wilcox, on Flickr

20180124_123545 by Gary Wilcox, on Flickr

20180124_123531 by Gary Wilcox, on Flickr

20180124_123526 by Gary Wilcox, on Flickr

I do have 1 question is it usual for the colour to come off onto the cloth ?

20180124_123428 by Gary Wilcox, on Flickr

20180124_123436 by Gary Wilcox, on Flickr

Should i have put another coat of the gloss on or maybe leave it longer before polishing up.

That's all for now thanks for taking the time to look and to comment.

Post by **pourquoi61** » Fri Jan 26, 2018 8:39 pm

Sorry I have no idea, but it looks fantastic.

Post by **gaz45** » Tue Jan 30, 2018 6:00 pm

Thanks mate

Post by **Twokidsnosleep** » Wed Jan 31, 2018 1:48 am

Looks pretty cool in WRB

If you are getting paint on the cloth you are getting through your clear coat and into the paint....careful

I like WRB, but our little STi has Cosmic Blue or blurple as some call it...have not seen that colour out yet for the 2012 Aoshima kit I have.

Post by **gaz45** » Wed Jan 31, 2018 10:42 am

Cheers mate thanks for the advice

Post by **Tay99** » Wed Jan 31, 2018 3:45 pm

Great build going on liking the interior, are the seat belts painted.

Post by **exmoor** » Wed Jan 31, 2018 9:45 pm

looking awsome gary great work

Post by **gaz45** » Thu Feb 01, 2018 9:28 pm

Tay99 wrote: Wed Jan 31, 2018 3:45 pm Great build going on liking the interior, are the seat belts painted.

No mate the belts are the kit decals

Post by **gaz45** » Fri Feb 09, 2018 2:38 pm

Time to work on the body, Just a little work to be done on a seams on the front and rear bumper these will be sanded away using the different Ultimate grade sanders they are still visible after sanding and polishing but they are smooth so they shouldn't be seen when primed and painted.

20180130_111718 by Gary Wilcox, on Flickr

20180130_111733 by Gary Wilcox, on Flickr

20180130_104218 by Gary Wilcox, on Flickr

20180130_111700 by Gary Wilcox, on Flickr

There is some extra plastic to be removed from the front grille badge this i will carefully remove this with a fine razor saw.

20180130_104250 by Gary Wilcox, on Flickr

20180130_112721 by Gary Wilcox, on Flickr

20180130_112716 by Gary Wilcox, on Flickr

I will now clean up and add some of the body parts that can be painted on the body in the body colour. [One thing to note is with the door mirrors as there is only one of these to be fitted and depending which number/driver decal you use will depend on which side the mirror will be fitted]. The spoiler will be glued together and painted sepperatly. the other parts i will glue in place from the inside where i can to avoid any glue on the surface.

20180130_120844 by Gary Wilcox, on Flickr

20180130_123845 by Gary Wilcox, on Flickr

20180130_123854 by Gary Wilcox, on Flickr

Now to clean up the remainder of the parts that are painted in different colours that will be added at the end of the build.

20180130_133033 by Gary Wilcox, on Flickr

20180130_142027 by Gary Wilcox, on Flickr

There is a mask set for the windows but i did need to trim the front and rear masks.

20180130_124645 by Gary Wilcox, on Flickr

20180130_132315 by Gary Wilcox, on Flickr

I have stretched some sprue by heating it up a little with a lighter to make the antennas, which will be painted and cut to length before fitting.

20180130_135943 by Gary Wilcox, on Flickr

So the white Ultimate primer on and dry and a little sanding back with a Ultimate sponge sander to remove any high spots ready for the Blue paint.

20180131_114911 by Gary Wilcox, on Flickr

20180131_114920 by Gary Wilcox, on Flickr

With all that done it's time to lay down the colour so about 3 light coats of the Zeropaints world rally blue and now it will be left for at least 24 hours to set up before apllying the decals.

20180205_123824 by Gary Wilcox, on Flickr

20180205_123840 by Gary Wilcox, on Flickr

20180205_123855 by Gary Wilcox, on Flickr

20180205_123913 by Gary Wilcox, on Flickr

20180205_123945 by Gary Wilcox, on Flickr

Right on with the decals I've got my water on a mug warmer keeping warm and my setting solutions to hand

20180206_124610 by Gary Wilcox, on Flickr

20180206_124631 by Gary Wilcox, on Flickr

My decalling still needs a little bit more work i think i may be working them too much, but following Pauls decalling guide it has made it so much easier.
All the decals are now on and will be left to cure before putting on the gloss coat.

20180207_202431 by Gary Wilcox, on Flickr

20180207_200902 by Gary Wilcox, on Flickr

20180207_200934 by Gary Wilcox, on Flickr

20180207_200941 by Gary Wilcox, on Flickr

20180207_201015 by Gary Wilcox, on Flickr

20180207_201033 by Gary Wilcox, on Flickr

20180207_201040 by Gary Wilcox, on Flickr

20180207_201048 by Gary Wilcox, on Flickr

20180207_201102 by Gary Wilcox, on Flickr

20180207_201158 by Gary Wilcox, on Flickr

That's where it stands for now thanks for looking and for all your comments.

Post by **DrSprue** » Fri Feb 09, 2018 2:55 pm

Wow just awesome detailing and precision with that kit Gary!

Post by **gaz45** » Fri Feb 09, 2018 3:03 pm

Thanks Tony

Post by **Paul** » Fri Feb 09, 2018 4:10 pm

Great work Gaz, nice job

Post by **gaz45** » Fri Feb 09, 2018 4:12 pm

Thanks Paul

YouTube · Post by **OlaHansson** » Sat Feb 10, 2018 8:47 am

Wow looks great!

Post by **gaz45** » Sat Feb 10, 2018 8:15 pm

Cheers mate

Post by **demarcation** » Sun Feb 11, 2018 12:44 am

Looks the part mate, beautiful job!!

Post by **gaz45** » Sun Feb 11, 2018 1:20 am

Thanks buddy

Post by **gaz45** » Tue Feb 27, 2018 3:06 pm

Time for an update i think it has been a while appologise

So it has been clear coated in AlcladII gloss and was left to dry over the weekend which turned out to be a week

and it will then get polished up the same way i did on the test piece.

As before i will be using the Zeropaints polishing compounds as before

20180222_190350 by Gary Wilcox, on Flickr

So all polished up and ready for the final detail painting.

20180222_192938 by Gary Wilcox, on Flickr

20180222_192958 by Gary Wilcox, on Flickr

20180222_193021 by Gary Wilcox, on Flickr

20180222_193042 by Gary Wilcox, on Flickr

The detail painting left to do is round the windows, the lights and the side inicators. now for the window edges i was going to use some masking tape and after the initial try it pulled up some of the decal.

20180223_153724 by Gary Wilcox, on Flickr

So free hand painting it is as you can probably see my hand was not that steady on this day but it is done now

20180227_131543 by Gary Wilcox, on Flickr

20180227_131548 by Gary Wilcox, on Flickr

20180227_131600 by Gary Wilcox, on Flickr

20180227_131611 by Gary Wilcox, on Flickr

So all that's left to do now is to fit the body to the chassis and add the last of the body parts.

Thanks for taking a look and for all your comments through this build.

Post by **gaz45** » Tue Mar 13, 2018 1:11 pm

Time to cut the mesh to size and fit this was done using TET which was a good job really has i glued the bigger mesh in the wrong place

20180228_133751 by Gary Wilcox, on Flickr

20180228_134813 by Gary Wilcox, on Flickr

Mesh corrected.

20180228_135438 by Gary Wilcox, on Flickr

20180228_135510 by Gary Wilcox, on Flickr

20180228_135448 by Gary Wilcox, on Flickr

The plates on the under side are now fitted

20180228_141052_HDR by Gary Wilcox, on Flickr

along with the windows

20180228_142120 by Gary Wilcox, on Flickr

20180228_142139 by Gary Wilcox, on Flickr

20180228_142130 by Gary Wilcox, on Flickr

Just a short update all that's left is to fit the lights, add the wipers, door mirror and the antenna's.

Thanks for taking the time to look and to comment
See you at the finish line.