1/25 scale 1922 Model T Touring Car

[Wolfman63]

For the next commission build I will be replicating a 1922 Ford Model T Touring for a close friend whose father recently passed away. The car was his pride and joy as he spent many years restoring it. The problem is there are no 1922 Model T Touring kits available. So after doing some research I found two kits that I can “kit bash” most of the parts and sections to replicate most of the vehicle and then scratch build any other specific parts for the 1922 Ford. I have multiple photos of the actual vehicle so this should be easy to replicate. The term “Kit Bash” is a modeling term where multiple parts from multiple kits are used to make a specific model. This will be the first time I will be using the kit bash method so this should be another interesting build. Side note – I started this late in the week as I was busy packing the previous commission and shipping it out to the client.
After researching the available models I ended up purchasing the AMT 1/25 scale ’23 T Depot Hack and the AMT 1/25 Vintage Police Car. The ‘23T has the correct fenders, front end, wheels, and frame. The Vintage Police Car has a similar body and roof. The police car is a 1927 T touring car. The doors, the area in front of the windshield, and the engine cowl are incorrect for a 1922. I started off by cutting the front section off the body. Using the reference photos I measured the correct size of the front end. I thought I could just shorten the front but then realized the engine cowl was smaller so the angle from windshield to cowl was different as well. I used the measurements of the correct cowl and scratch built the firewall. I then built a small frame to hold the firewall and some thin sheet styrene to scratch build the body panels. Due to the angle I ended up making three separate panels to form the angle and curves. These were then covered with a thin coat of putty. Once sanded and shaped will match the reference photos correctly.
As for the doors I will make the door edges with wire and then use a thicker wire for the hinges. I will sand off the kit door edges and then install the formed wires. The rear doors need to be reshaped and have the hinges move to the other side of the rear doors as they are hinged from the rear side of the door.
The plan is to complete the body this coming week then assemble the frame and suspension.
You can see all the photos and details from start in the build log at: https://davidsscalemodels.com/build-log ... uring-car/

[Twokidsnosleep]

Super project

[Wolfman63]

The second week of the T Touring car was spent working on the changes to the body. The differences were the section in front of the windshield and the rear doors. After roughing in the front section I laid in some putty and then wet sanded it into shape. For the rear doors the shape of the doors was incorrect and I needed to relocate the hinges. I sanded down the molded lines. I used 30 gauge wire and formed the door edges then used photo etch scraps to make the hinges. Since the door edges and hinges were not exactly like the new rear doors I sanded the front door area down and replicated them with the wire and photo etch as well. I then primed the body with white primer.
While some steps of modifying the body required drying time I started working on the chassis. I started with the wheels and tires. I purchased some gold paint pens as this build has a lot of gold accents. The outer ring and the center cap of the wheels were painted gold while the spokes were painted wood and the hubs were black. The vinyl tires were then installed. I also painted the spare tire with the gold rim and black tire cover. The “FORD” logo on the tire cover was then painted white using a pointed micro brush. The frame was assembled along with the suspension. The engine and transmission were assembled and installed on to the frame. With the chassis mostly done I set it aside and turned back to the body.
The body, cowl, and radiator frame were then paint with gloss red. The fenders/ running boards were then painted gloss black. The next part of the body is the frame for the windshield. I used styrene rod to for the outside frame. I am using clear styrene sheet for the windshield. I need to cut the windshield along the center to replicate the weather strip between the two sections. I am thinking of using some very thin shrink tubing for this.
I have some more detailing on the chassis then fitting the body on to the chassis. It does look like I may need to make some minor adjustments so the body sits correctly I also need to scratch build the mount for the spare tire on the rear, the front and rear turn signal lights, license plate frames, the horn on the driver side door, and the brake light. I also ordered the nameplate as well as a nice display case from Grandpa’s Cabinets.
You can see all the photos and details from start in the build log at: https://davidsscalemodels.com/build-log ... uring-car/

[barryf1fan]

Very cool project!! And kudos for doing this kit for your friend. Off to a great start, and is that the "dad's" car in the pic sitting on your paint bottles?? What a cool car - my Uncle Bob just passed away a couple months ago and he had a Model T and a Model A, among a few other really cool cars. He had a 1935 Chevy pickup that was his dad's (and my mom's ) and it was basically bone stock. I loved going to their house to sit out in the garage with him (he had two girls...) and my brother to just listen to him talk and go for rides.

Anyway, this will probably mean more to you friend than he could probably ever express... can't wait to see it complete.

[Wolfman63]

Very cool project!! And kudos for doing this kit for your friend. Off to a great start, and is that the "dad's" car in the pic sitting on your paint bottles?? What a cool car - my Uncle Bob just passed away a couple months ago and he had a Model T and a Model A, among a few other really cool cars. He had a 1935 Chevy pickup that was his dad's (and my mom's ) and it was basically bone stock. I loved going to their house to sit out in the garage with him (he had two girls...) and my brother to just listen to him talk and go for rides.

Anyway, this will probably mean more to you friend than he could probably ever express... can't wait to see it complete.

Thank you. Yes that is the actual car. On my blog it is the title photo in the build log page.

[Wolfman63]

The third week of the Model T Touring I installed the body to the chassis. This took some time to get it to sit correctly on the chassis. The fenders are separate pieces so getting them to sit on the chassis and lined up took some time. The interior was painted and front seat was installed. I then scratch built the front windshield using styrene rods and a clear styrene sheet. The side mirrors were made using styrene rod and some photo etch for the mounts.
The display case arrived this week from Grandpa’s Cabinets. I went with a red oak stained base that had a channel in it to hold the clear cover. I had this made a little larger as I will be mounting a small photo frame for the memorial photo and a brass etched name plate.
Next I started the other details like the steering wheel was assembled and painted. The dashboard was painted and the gauges were detailed. The canvass top was modified to have three rectangle windows to match the reference photos and then the top was painted with satin black. The actual car has two accessory lights on the front mounted on the body just behind the hood and two mounted on the chassis in the rear. These lights are to make the car street legal. To replicate these I started with styrene rods and made the light bezels out of wire.
One thing to note is the gold and chrome paint pens take 24 hours to dry so I have been bouncing around different areas. I started on the spare tire assembly. I need to make the mount for the rear of the car then make the license plate frames with another brake light. The actual car uses a legal antique license plate as well as a replica plate from 1922. There are a lot more details that requiring scratch building like the FORD logo on the radiator, Radiator cap, front license plates, a horn for the driver side door, and the support linkage for the top.
You can see all the photos and details from start in the build log at: https://davidsscalemodels.com/build-log ... uring-car/

[Wolfman63]

The fourth week of the Model T Touring I started assembling the car. The steering wheel and pedals were installed. I then installed the windshield assembly and the top. One of the details in the reference photos was an old style horn mounted on the driver side door edge. I scratch built this using different size wires and a styrene rod. The rod was placed in a drill and I used a rat tail file to shape the rod into the front of the horn. I used a candle to melt the end of another piece of rod to form the squeeze bulb of the horn.
The next thing I needed to replicate were the license plates for the front and back. I used the reference photos to make decals of the plates. I even added the registration sticker to the rear plate. These were then applied to the frames and mounted on the front and back of the car. On the radiator face was a “FORD” nameplate. This was replicated by printing the Ford logo on a piece of clear acetate in black then painting the black letters with the fine gold paint pen. I also used the gold paint pens to paint the step plates on the running boards.
With the car nearly assembled I just have a few more things to add like the linkage for the top and scratch build the auxiliary lights that mount just in front of the windshield. Then I can mount the car onto the display base and the other items that will go inside the case. Stay tuned for the final week of this memorable build.
You can see all the photos and details from start in the build log at: https://davidsscalemodels.com/build-log ... uring-car/

[digger303]

[Wolfman63]

The fifth week of the 1/25 scale 1922 Model T Touring I finished the project! To start with I mounted the car to the display base by running a wire thru the tires and into holes I drilled in the base. I then used some epoxy to secure the wires into the base. I purchased a small photo frame for the photo and then applied the nameplate. It was then delivered to the family.
The finished project came out great! This was the first time I kit bashed two models to make one replica. The AMT kits themselves gave me all the parts I needed and a little scratch building completed the finer details. The family was extremely happy with the final results.
You can see all the photos, details, and a video of the completed project in the build log at: https://davidsscalemodels.com/build-log ... uring-car/

[digger303]

Well done.