Global Scale Modeller

Cheers guys i'm still waiting for the cans to arrive from eduard

Fabulous work mate - this is coming along really well

Thanks mate

Just lovely the work that you have put into this kit.
Waiting for you to cross the winning line with this one.

Just a very quick update
The parts have arrived from eduard and they are the has i already have

20171122_131654 by Gary Wilcox, on Flickr

So what i intend to do next is see if i can work with these parts other wise i will use the kit plastic parts the only trouble with that the original hobby boss instructions for this kit show the exhausts being fitted before the fuselage halves go together and my halves are already together

Wish me luck

gaz45 wrote: Wed Nov 22, 2017 1:25 pm Wish me luck

Good luck!

I guess they must be correct then. I think you should cut them apart like you said before. They probably cast them all in one piece because it made most sense from a manufacturing point of view.

Cheers guys i will be trying that

Sorry for the delay guys i lost my mojo a little bit but it's coming back

Part 8
As i have said the replacement parts from eduard are the same as i already have and if i use the kit parts i will have to shorten them so they fit as the kit parts should be added before the 2 halves go together.

20171122_133228 by Gary Wilcox, on Flickr

So firstly try to make the resin parts look good while looking over the parts trying to see the best place to cut there was movement and pop the piece with the blades on just slid out so they were the correct pieces after all 1 piece was just slotted into the other so they just slide out then you rotate them and there you go 2 exhausts as seen in the instructions so no extra cutting

20171128_093514 by Gary Wilcox, on Flickr

20171128_093538 by Gary Wilcox, on Flickr

So onward with the build
The parts are trimmed up ready foe the PE

20171128_100725 by Gary Wilcox, on Flickr

and the PE

20171128_112257 by Gary Wilcox, on Flickr

20171128_122016 by Gary Wilcox, on Flickr

20171128_123039 by Gary Wilcox, on Flickr

when these are set they will be primed.
The exhaust covers are cleaned up ready for fitting and the stabilizers

20171128_125915 by Gary Wilcox, on Flickr

20171128_131354 by Gary Wilcox, on Flickr

The exhausts have been primed in Ultimate glossy black primer

20171128_144836 by Gary Wilcox, on Flickr

and once dry painted up in mr metal color iron and awaiting being buffed up

20171129_112155 by Gary Wilcox, on Flickr

The exhaust covers are glued on and the stabilizers are just push fit in place

20171129_121702 by Gary Wilcox, on Flickr

The exhaust parts are now polished up for this i used some cotton buds except for where the PE was i used a small stiff paint brush

20171129_123757 by Gary Wilcox, on Flickr

20171129_123814 by Gary Wilcox, on Flickr

20171129_123837 by Gary Wilcox, on Flickr

20171129_123854 by Gary Wilcox, on Flickr

20171129_123903 by Gary Wilcox, on Flickr

I have masked up the canopy with the supplied mask set and to me something didn't look right there seams to be too much exposed glass to be painted so i filled the rest with some Tamiya masking tape.

20171130_132916 by Gary Wilcox, on Flickr

20171130_132921 by Gary Wilcox, on Flickr

20171130_132928 by Gary Wilcox, on Flickr

20171130_134242 by Gary Wilcox, on Flickr

That looks better

The wheel well covers were cleaned up and the inside surfaces were painted in Ultimate white primer

20171130_134918 by Gary Wilcox, on Flickr

The landing hook built

20171130_135057 by Gary Wilcox, on Flickr

The AIM 54 brackets

20171130_190503 by Gary Wilcox, on Flickr

20171130_205323 by Gary Wilcox, on Flickr

20171130_205343 by Gary Wilcox, on Flickr

This is where the TARPS will sit

20171130_205421 by Gary Wilcox, on Flickr

The brackets for the AIM 9 and 7

20171130_205615 by Gary Wilcox, on Flickr

and finally the rudders glued in place

20171130_210300 by Gary Wilcox, on Flickr

20171130_210306 by Gary Wilcox, on Flickr

20171130_210321 by Gary Wilcox, on Flickr

Looking like a plane now
Just a little filling and sanding then it will be time for primer and paint finally the finish line is in sight

Thanks for taking a look and for all your comments

Looking good!

Wow!

Awesome stuff going on there, mate!

The burner cans from Eduard was well worth the wait - they look amazing


Tommy

Thanks guys much appreciated

Here we are Part 9
I have done the masking of the wheel wells ready for priming in Ultimate black primer

20171204_165235 by Gary Wilcox, on Flickr

20171204_165243 by Gary Wilcox, on Flickr

20171204_165305 by Gary Wilcox, on Flickr

20171204_165321 by Gary Wilcox, on Flickr

20171204_165329 by Gary Wilcox, on Flickr

The front of the nose cone has been painted with mr hobby H-318 Radome the main body color is mr hobby H-325 gray FS26440
I have already used 1 pot of paint to get this far and i have 1 more pot i hope this will be enough

20171206_132208 by Gary Wilcox, on Flickr

All painted now with just a little paint spare for any touch up

20171206_235208 by Gary Wilcox, on Flickr

Once this is all cured it will be clear coated with a 50-50 mix of tamiya x-22 and mrcolor leveling/thinner in preperation for the decals

That's where it stands now

Looking good. They do drink up the paint!

Thanks mate yes they do

Nice work Gaz, those exhaust cans were definitely worth the wait.

Thanks they were once i figured that they were the right ones in the first place

Part 10 the final part

Right time to put on the decals there are quite a few of these so it may take some time. I have noticed while doing these that there are some parts in the illustrations used for the placement of the decals differ from the actual parts. however they did go down well.

20171222_171941 by Gary Wilcox, on Flickr

20171222_171947 by Gary Wilcox, on Flickr

20171222_171949 by Gary Wilcox, on Flickr

20171222_171952 by Gary Wilcox, on Flickr

20171222_171959 by Gary Wilcox, on Flickr

20171222_172008 by Gary Wilcox, on Flickr

20171222_172028 by Gary Wilcox, on Flickr

20171222_172032 by Gary Wilcox, on Flickr

20171222_172051 by Gary Wilcox, on Flickr

20171222_172057 by Gary Wilcox, on Flickr

20171222_172103 by Gary Wilcox, on Flickr

The resin wheels are all finished they were painted up with Ultimate white primer and akah tire black these have now been added along with the fuel tanks and missiles. I forgot to mention this was all given a flat coat using Tamiya XF-86 flat clear.

20171228_154640 by Gary Wilcox, on Flickr

20171229_094232 by Gary Wilcox, on Flickr

20171229_094254 by Gary Wilcox, on Flickr

20171229_094305 by Gary Wilcox, on Flickr

20171229_094334 by Gary Wilcox, on Flickr

20171229_094345 by Gary Wilcox, on Flickr

So there we are i'll call that finished.I would have liked to do a little weathering on this but time will not allow. Thanks for taking a look and for all your comments along the way.
I will post some photos in the reveal section.

Just in time! Nice job!

Yeah thanks mate