It's Friday nights live at the bench hat have you been working on for Friday July 21st

[Kingdan]

"WHAT HAVE YOU BEEN WORKING ON THIS WEEK?" - A NEW SEGMENT OF FRIDAY NIGHT'S ISM LIVE "AT THE BENCH" SHOW!

* Open now until 1 hour before the show on Friday, July 21st*

** PLEASE read ALL of the rules below carefully! **

Hello everyone! This post is being created to give you, as a member of ISM, the opportunity to share what you have been working on during the week on the Friday night show. Please read the rules below in order to participate.

01). By participating in this thread, you are giving permission for the ISM live crew to share your work during the Youtube broadcast of the ISM Live "At the Bench" Friday show.

02). Please, only post your own work and not that of others.

03). Remember, post only one image per member each week. This will prevent prolific builders from dominating this segment and will prevent this part of the show from becoming too long.

04). Also, have only one project shown in the image per member each week. Again, this prevents prolific builders from dominating this segment and making this segment longer than it needs to be.

05). Along with your image, please include the following details: The name of the kit; the company that produces the kit; any aftermarket that you have added, along with the brands and colors of paint used (if applicable).

06). The deadline for entries each week will be between the time the post goes up until an hour before Friday's show. Entries made after the deadline will not be shown.

07). Remember: If you wish to have a project highlighted during the show, the image and information must be shared in this thread, not a separate post on the Facebook page!

08). There will be a posted thread similar to this one on the ISM Forums. PLEASE post your work only in ONE of these. This will prevent us from having to sort through duplicate posts on both sites.

After the the live crew shows what they have been working on during the week, participating member's images and details will then be shown. This is an opportunity for you as members to be directly involved with the show. We hope that you will participate no matter your level of experience. This will not be a critique of anyone's work.

We thank you in advance for allowing us the opportunity to showcase your models! - Lee Larholt, Paul Bretland, and the rest of the ISM moderators and live crew.

[Twokidsnosleep]

HiHo DANNO!!!!
Ooo Ooo I am first in line.



Revell 1/390 Air Canada Boeing 747-200
SMD LEd's now with a wicked evil looking red one!!
BMF on wings...matt aluminum and shiny chrome I think they were

[ElCapitan]

Did some weathering on the Trumpeter Mig-29A. Used Mig Jimenez panel line wash to give a general dirty effect.

[Stokesy44]

Nuts Planet 1/10 101st Airborne Trooper

At the priming stage. Arms and ruck attached to torso. Just needed a tiny bit of filler at the shoulders. All parts cleaned and mounted ready to go.

The kit is a thing of beauty. The quality of the mould is amazing, the uniform creasing, the detail on the harness, the clasps and all the bits of equipment. Not to mention the rather eerie resemblance to Damien Lewis

IMG_5567 by David Stokes, on Flickr

[Tomcat64]

My A-10A & T-72 for the warring weather GB is just about done

The A-10 has been finished off with a couple of coats of Alclad Aqua Gloss, then AK Ultra Matte and finally weathered with a dark dirt clay wash. I wanted a reasonable grubby finish so used the Matte finish before the clay wash so that it left streaks and stains in the same way I'd weather an AFV. Finally the ordnance was added and everything sealed up with a final coat of Ultra Matte before unsealing the cockpit and picking out the nav lights with Vallejo model colour.

The base is a 6x6inch piece of foam-board with a Games Workshop flying base installed to take the Perspex rod for the plane. This has been built up with a combination of Tamiya light sand textured paint, small stones, and MiG pigments desert storm sand. The debris from the busted T-72 is small slate mixed with Humbrol Smoke powder and a combination of thin PVA (which didn't hold well enough - should have used thicker glue) and thin CA to hold it all in place.

All I need to do now is add the rod & A-10 for the final reveal shots.

[Kingdan]

Some excellent offerings this week cheers chaps