Global Scale Modeller

Hi guys
So this is my first entry in this sig
The kit will be Revell's massive B-1B in 1/48 scale wich messures about 90 cm long and 86 cm wide or 36 inches long and 34.5 inches wide (roughly) for the golks on the other side of the North Sea
So quite big by any standard
This is the kit that i really wanted to get for this build as it is one of the very few bombers i build before
I had this kit once before but that one fell down a closet and it didn't survive it's close encounter with the floor
So my choise is only based on nostalgia and the idea i can do a better job now then 15 years ago

So wich kit is it?

20180428_235408 by Mark Verploeg - Flickr2BBcode LITE
This is the 2000 rebox version of this kit
The kit was "born" in 1983 so 3 years older then the modeller building it but for the age i think it looks pretty good
It was released/reboxed several times over the years both under the Revell and Monogram names
The last time was in 2015 under the Revell name as a limited edition

And what is in the huge (coffee table sized) box

20180428_235412 by Mark Verploeg - Flickr2BBcode LITE
Well this pile is in the box


20180429_000102 by Mark Verploeg - Flickr2BBcode LITE

20180429_000124 by Mark Verploeg - Flickr2BBcode LITE

20180429_000157 by Mark Verploeg - Flickr2BBcode LITE

20180429_000223 by Mark Verploeg - Flickr2BBcode LITE

20180429_000418 by Mark Verploeg - Flickr2BBcode LITE

20180429_000836 by Mark Verploeg - Flickr2BBcode LITE

20180429_001251 by Mark Verploeg - Flickr2BBcode LITE

20180429_001343 by Mark Verploeg - Flickr2BBcode LITE

20180429_001840 by Mark Verploeg - Flickr2BBcode LITE

20180429_001853 by Mark Verploeg - Flickr2BBcode LITE

20180429_001906 by Mark Verploeg - Flickr2BBcode LITE

20180429_001916 by Mark Verploeg - Flickr2BBcode LITE

20180429_001955 by Mark Verploeg - Flickr2BBcode LITE

20180429_002116 by Mark Verploeg - Flickr2BBcode LITE
So these are all the parts
As you can see by the masking tape i had quite a few parts that snapped from the sprues
But ofcourse we also have

20180429_002218 by Mark Verploeg - Flickr2BBcode LITE
Decals

20180429_002239 by Mark Verploeg - Flickr2BBcode LITE
And some yellowish instructions

And because it isn't the newest i decided to get a couple of after market goodies

20180429_002255 by Mark Verploeg - Flickr2BBcode LITE

20180429_002343 by Mark Verploeg - Flickr2BBcode LITE
I think i will be using this set of decals


20180429_002415 by Mark Verploeg - Flickr2BBcode LITE
A mask set that includes the metallic colored edge of the glass


20180429_002424 by Mark Verploeg - Flickr2BBcode LITE
Eduard exhaust set


20180429_002437 by Mark Verploeg - Flickr2BBcode LITE
And a Eduard Big Ed set

And that is the kit and what i will be using for the build
Just one more night of sleep to go and then i can start

And that is all i have for now
I am looking forward to this build and all the builds you guy come up with
So the best of luck with everyones builds
Take care
Cheers
Mark

That is a big boy! I got to see one fly at an airshow years ago - the sound rumbles right through you like a freight train! I'd love one but at a smaller scale!

They are big indeed
About 40 meters long in real life
The power of those engines must be huge as i have seen a clip where grown up get tossed around like rag dolls
But then again they where walking behind it while it was about to take off
There are some smaller kits of it aswell
I just wanted this big bird again ,i missed it for many years

Side by side - brothers from a different age!

Bombers by Donald Miller, on Flickr

Very cool build indeed
Thank you for putting your # in the title..most helpful mate
Good luck, this will be a fantastic build

DBMiller wrote: Mon Apr 30, 2018 3:01 pm Side by side - brothers from a different age!

Bombers by Donald Miller, on Flickr

It looks small like this
But then again the B-52 is really big

Twokidsnosleep wrote: Mon Apr 30, 2018 5:09 pm Very cool build indeed
Thank you for putting your # in the title..most helpful mate
Good luck, this will be a fantastic build

No problem
I saw someone do it before me so i figured it was a good idea and just stole it

Hope you've got a big bench for that bone Mark. It looks like a superb kit.

Look forward to the progress on this one.

Good Luck, Les

Thanks again Les
I have quite a large bench actually
2 120x80 cm tables
But these big kit boxes take up quite a lot of space
I started with the HE-111 today and then the B-1B is next or the T-10M i will be building for the Cold War GB
Then i will have enough free space on the bench for this big bird

Good luck with this! I have one I am in the process of building myself. Started long before this SIG fired up. I had put it to the side for a bit. May fiddle with it while I am doing my build here.

Look forward to seeing yours!

Thanks
I hope to get a bit of a start on it today
My Heinkel build is at a point that i need to start painting so this one is next to get the interior build up
Up to the point i need to paint it anyway as i have the colored pe for the cockpit
But with the Lancer i also want to have the landing gear bays and bombbays ready before i start building up fuselage parts

Looking forward to this one! I used to have the same kit with all the goodies, I had to be realistic as to where I could display it once built, so ended up passing it on
One recommendation if you hadn't considered it already, would be to use the SAC metal landing gear set in place of the kit flimsy plastic ones, plenty of strength and more detail too
All the best with the build

Great looking aircraft, good luck with the build mate

InvalidUsername wrote: Wed May 02, 2018 10:46 pm Looking forward to this one! I used to have the same kit with all the goodies, I had to be realistic as to where I could display it once built, so ended up passing it on
One recommendation if you hadn't considered it already, would be to use the SAC metal landing gear set in place of the kit flimsy plastic ones, plenty of strength and more detail too
All the best with the build

I have thought about it but no shop i know has that set at the moment
I was planning on drilling some holes in the landing gear and adding some metal or rod in it to make it a bit stronger

Kevthemodeller wrote: Wed May 02, 2018 11:04 pm Great looking aircraft, good luck with the build mate

Thanks Kev

Order them straight from SAC. That's what I did.

http://www.scaleaircraftconversions.com ... imeout=500

I thought about doing it but i think i will just use the kit parts
With a couple of metal rods in the landing gear it will be quite sturdy
And i think this build is expensive enough as it is at the moment
That is one big reason for me anyway

MarkVerploeg wrote: Fri May 04, 2018 1:33 pm I thought about doing it but i think i will just use the kit parts
With a couple of metal rods in the landing gear it will be quite sturdy
And i think this build is expensive enough as it is at the moment
That is one big reason for me anyway

I can totally understand that!

Great banter. When ya gonna build it Mark?

Only joking mate. My Dambuster Lancaster is still at my old house so you're doing better than I am.

Stokesy44 wrote: Sat May 05, 2018 9:03 am Great banter. When ya gonna build it Mark?

Only joking mate. My Dambuster Lancaster is still at my old house so you're doing better than I am.

I hope to get something done today but currently it is quite busy at work
But just 2 more days and then i have a couple of days off so atleast monday should be for modelling

MarkVerploeg wrote: Sat May 05, 2018 2:08 pm I hope to get something done today but currently it is quite busy at work
But just 2 more days and then i have a couple of days off so atleast monday should be for modelling

Mate you've got my full sympathy I'm in the same boat of late, not got anywhere near mine as yet

Going to be watching this one with interest - not least to see how a kit this size supports its own weight in plastic

Tomcat64 wrote: Sun May 06, 2018 8:54 am Going to be watching this one with interest - not least to see how a kit this size supports its own weight in plastic

With pure luck probably

Hi guys
Time for an update i think as the first parts are primed at the moment


20180507_122338 by Mark Verploeg - Flickr2BBcode LITE
Work starts with the front landing gear bay


20180507_122855 by Mark Verploeg - Flickr2BBcode LITE
Side walls where added


20180507_124942 by Mark Verploeg - Flickr2BBcode LITE
Front and rear cockpit sections
The rear section is glued together but the front isn't because of the colored photo etch that needs to be added after painting


20180507_124949 by Mark Verploeg - Flickr2BBcode LITE
From a different angle


20180507_125158 by Mark Verploeg - Flickr2BBcode LITE
How it should look


20180507_134901 by Mark Verploeg - Flickr2BBcode LITE
Adding some pe


20180507_141621 by Mark Verploeg - Flickr2BBcode LITE
The reworked ladder with pe parts


20180507_141624 by Mark Verploeg - Flickr2BBcode LITE
From the side


20180507_142253 by Mark Verploeg - Flickr2BBcode LITE
Some pe in the rear cockpit section
The colored parts get added after painting


20180507_221600 by Mark Verploeg - Flickr2BBcode LITE
The "bang" seats


20180507_221725 by Mark Verploeg - Flickr2BBcode LITE
All the interior parts for the front section of the plane


20180508_000206 by Mark Verploeg - Flickr2BBcode LITE
Main landing gear bay with the pe panels


20180508_000716 by Mark Verploeg - Flickr2BBcode LITE
Rotary pylons and internal spare fuel tank (i think)
I don't know if they can drop that thing or not



20180508_003305 by Mark Verploeg - Flickr2BBcode LITE
The bomb bay sections will be assembled after painting


20180508_193048 by Mark Verploeg - Flickr2BBcode LITE
The payload for the rotary system
They are some sort of short range air to ground missile (atleast that is what i was told)
I thought they where B83 nukes


20180508_194242 by Mark Verploeg - Flickr2BBcode LITE
Missiles are fitted


20180508_225826 by Mark Verploeg - Flickr2BBcode LITE
And everything was primed along with the parts of the Heinkel HE-111

And that is where this (and the Heinkel) build is at right now
I hope to get some painting done in the next couple of days but i also started the T-10M build for the Cold War GB and currently there are a lot of parts cleaned but still not assembled on the bench so i need to take care of that first

Thanks for stopping by and having a look
Take care
Cheers
Mark

That's an impressive collection of components already Mark - the PE really just lifts the details to another level. Nice work

Thanks Neil
I agree it adds a bit of detail but most will be hidden once it is assembled
The most exterior parts are those small fins near the tail and static dischargers wich hopefull don't fall off

Doing great
Quite an array of scary weaponry

Interior detail looks good, especially with the extra magic of the PE stuff.

Looks a bit on the large side me thinks!!

Twokidsnosleep wrote: Thu May 10, 2018 5:32 pm Doing great
Quite an array of scary weaponry

Thank you

Stokesy44 wrote: Thu May 10, 2018 10:15 pm Interior detail looks good, especially with the extra magic of the PE stuff.

Looks a bit on the large side me thinks!!

As a kit or out of scale
The kit is a wee bit on the large size

Great start there mate some very nice detail

Thanks Gaz
The detail on the kit isn't bad
Considering it is a 1983 mold
But a couple of pieces of photo etch make it a bit more intresting in the end

MarkVerploeg wrote: Thu May 10, 2018 11:20 pm

Twokidsnosleep wrote: Thu May 10, 2018 5:32 pm Doing great
Quite an array of scary weaponry

Thank you

Stokesy44 wrote: Thu May 10, 2018 10:15 pm Interior detail looks good, especially with the extra magic of the PE stuff.

Looks a bit on the large side me thinks!!

As a kit or out of scale
The kit is a wee bit on the large size

It's going great, but you might have to order some paint. That's a lot of kit.

Wow that is coming together great, impressive PE work

Les

digger303 wrote: Sun May 13, 2018 2:09 am

MarkVerploeg wrote: Thu May 10, 2018 11:20 pm

Twokidsnosleep wrote: Thu May 10, 2018 5:32 pm Doing great
Quite an array of scary weaponry

Thank you

Stokesy44 wrote: Thu May 10, 2018 10:15 pm Interior detail looks good, especially with the extra magic of the PE stuff.

Looks a bit on the large side me thinks!!

As a kit or out of scale
The kit is a wee bit on the large size

It's going great, but you might have to order some paint. That's a lot of kit.

True ,it is big but as i am going for just the grey finish that the Lancers currently have i ordered 3 bottles of the H305 wich is the FS color i need
It looks a bit light but on a black primer it should work
I started painting today and the base colors of the interior are done so just detail painting left to do
But during the gathering of the paints i need for my builds i found i may have to visit the LHS soon ss i don't have enough paint for the Heinkel

Les0012 wrote: Sun May 13, 2018 9:26 am Wow that is coming together great, impressive PE work

Les

Thanks
This kind of pe work is not that hard and i kind of like doing this
I find the armor pe a bit harder with parts like ammo tubes and working hinges
Those take practice and patience (wich is in short supply sometimes)

Beautiful work bones.

Thank you

Door prize draw coming up this weekend

Hi guys
So it is time for another update
I managed to make quite a lot of progres the past 2 days and i don't want to jam all of construction in just 1 update
So this will be for the big parts of the construction and the next update will be for the detailing ....well that is the plan anyway

So what happened since last time

20180513_101601 by Mark Verploeg - Flickr2BBcode LITE
I started out with basepainting the interior parts
H308 for the grey bits and Tamiya XF-2 flat white


20180514_134857 by Mark Verploeg - Flickr2BBcode LITE
For the missiles i used some ordinary paper wich i rolled up into a tube to mask the centre of the rotary pylon
Then i used H330 grey as the color for the missles


20180514_135149 by Mark Verploeg - Flickr2BBcode LITE
Then the bomb bay interior parts where painted
I used modelcolor khaki and orange brown for the wires
The dark wires where painted with dark rubber from Vallejo's panzer aces range


20180514_162317 by Mark Verploeg - Flickr2BBcode LITE
While that was drying i added the colored pe in the cockpit


20180514_162331 by Mark Verploeg - Flickr2BBcode LITE
And in the rear compartment


20180514_162617 by Mark Verploeg - Flickr2BBcode LITE
The the front and rear cockpit sections ahere glued to the landing gear bay


20180514_162814 by Mark Verploeg - Flickr2BBcode LITE
And testfitted in the fuselage


20180514_215553 by Mark Verploeg - Flickr2BBcode LITE
The the 4 ejectionseats where finished with the colored pe parts
And everything was gloss coated with Alclad Aqua gloss



20180515_105419 by Mark Verploeg - Flickr2BBcode LITE
Then all the parts where given a wash
I used 2 Mig productions washes for this
I used the dark wash (brown but almost black) for the wires and all the grey parts
And neutral wash (a sandy grey color) for the white parts


20180515_105423 by Mark Verploeg - Flickr2BBcode LITE
The main landing gear bay


20180515_111622 by Mark Verploeg - Flickr2BBcode LITE
After a little bit of cleaning it lokked like this


20180515_111628 by Mark Verploeg - Flickr2BBcode LITE

20180515_111631 by Mark Verploeg - Flickr2BBcode LITE

20180515_111634 by Mark Verploeg - Flickr2BBcode LITE

20180515_111646 by Mark Verploeg - Flickr2BBcode LITE

20180515_111656 by Mark Verploeg - Flickr2BBcode LITE

20180515_111710 by Mark Verploeg - Flickr2BBcode LITE
Once the last bit of the thinner was dry i started to matt coat it using Vallejo matt varnish (the UV resistant one)


20180515_142502 by Mark Verploeg - Flickr2BBcode LITE
And once that was dry i started to assemble all the parts


20180515_142906 by Mark Verploeg - Flickr2BBcode LITE
With the missile loaded rotary system in place


20180515_143340 by Mark Verploeg - Flickr2BBcode LITE
The rear bomb bay wich in this case will house a spare fuel tank


20180515_143348 by Mark Verploeg - Flickr2BBcode LITE
The finished main landing gear bay


20180515_143504 by Mark Verploeg - Flickr2BBcode LITE
All the parts that need to go on the lower half of the middle fuselage piece


20180515_144204 by Mark Verploeg - Flickr2BBcode LITE
The landing gear bay and rear bomb bay where added first


20180515_145008 by Mark Verploeg - Flickr2BBcode LITE
And then the 2 other bomb bays


20180515_145026 by Mark Verploeg - Flickr2BBcode LITE
How it looks from the bottom


20180515_145725 by Mark Verploeg - Flickr2BBcode LITE
For the weight that needs to be added i used some ordinary nails
Those where packaged in some masking tape and then taped and glued to the sides of the fuselage


20180515_143930 by Mark Verploeg - Flickr2BBcode LITE
I then added the ejection seats to the cockpit


20180515_143937 by Mark Verploeg - Flickr2BBcode LITE

20180515_143942 by Mark Verploeg - Flickr2BBcode LITE

20180515_143944 by Mark Verploeg - Flickr2BBcode LITE
How it looks from various angles


20180515_145849 by Mark Verploeg - Flickr2BBcode LITE
Then the interior part was glued in the fuselage


20180515_150254 by Mark Verploeg - Flickr2BBcode LITE
And the fuselage halfs where glued together


20180515_151333 by Mark Verploeg - Flickr2BBcode LITE
The tailsection was made
This part is very easy as it only consists of 7 parts


20180515_161537 by Mark Verploeg - Flickr2BBcode LITE
The wings where put together and placed on the lower fuselage half


20180515_162036 by Mark Verploeg - Flickr2BBcode LITE
And the upper piece was glued on
These are very big and relatively thin parts so they warped a bit and had to be forced in place
I still had to remove quite a big seam on one side though


20180515_163121 by Mark Verploeg - Flickr2BBcode LITE
The engine parts where put together with the exception of the nozzles as those will be photo etched parts wich i will add later on


20180515_163712 by Mark Verploeg - Flickr2BBcode LITE
All the big pieces are ready to be glued together


20180515_164304 by Mark Verploeg - Flickr2BBcode LITE

20180515_164331 by Mark Verploeg - Flickr2BBcode LITE
And they are glued together
Just the engines to do at this point


20180515_164456 by Mark Verploeg - Flickr2BBcode LITE
And to get a idea of the size of this thing
I placed my 1/48 scale Flanker and Fulcrum next to the Lancer
The Flanker is a big fighter but the Lancer is easily double the size in any direction

And that is all i have for now
I hooe you like it so far and maybe someone else is going to build one of these monsters (who knows maybe i'm not the only one ready for the nuthouse )

Thanks for stopping by and gaving a look
Take care
Cheers
Mark

I put one aside a little while ago. I will get back to it after this build I believe. Great job with yours so far!

I chose to do the bomb bays closed though.

It's massive and so much detail. Even if it is molded on...it looks a great kit.
Absolutely love that coloured PE and that molded on detail is painted with mostly a very steady hand. Damned if I can control my paint as well.

Very nice build so far. I have one of these sitting awaiting its turn.

Your build is inspiring.

Keep up the great work...

Fantastic work - that is one big bird!

smokeriderdon wrote: Tue May 15, 2018 11:39 pm I put one aside a little while ago. I will get back to it after this build I believe. Great job with yours so far!

I chose to do the bomb bays closed though.

Thank you
It is a option to keep those doors closed ofcourse but i wanted them open on this one
They are pretty big so when they are open it allows for a good view inside
When you pick this big thing up anyway

digger303 wrote: Wed May 16, 2018 4:57 am It's massive and so much detail. Even if it is molded on...it looks a great kit.
Absolutely love that coloured PE and that molded on detail is painted with mostly a very steady hand. Damned if I can control my paint as well.

Thank you Digger
I had to do quite a couple of touch ups though
But i tend to add a little bit of water to Vallejo paints to thin them a little
They flow better that way making painting easier

DRUMS01 wrote: Wed May 16, 2018 5:44 am Very nice build so far. I have one of these sitting awaiting its turn.

Your build is inspiring.

Keep up the great work...

Thank you
It is worth the efferd of building one
They certainly are quite the eyecatcher when they are done
Well they are hard to miss really

sheppsea wrote: Wed May 16, 2018 6:28 am Fantastic work - that is one big bird!

thank you Sheppsea

Great work on all the internal bays. They look superb with all that detail and weathering.

Top stuff

Holy snapping Duck Sh*t Batman.... that thing is huge!

Stunning work there mate

Stokesy44 wrote: Wed May 16, 2018 8:59 am Great work on all the internal bays. They look superb with all that detail and weathering.

Top stuff

Thanks Stokesy

Fridgy wrote: Wed May 16, 2018 11:10 am Holy snapping Duck Sh*t Batman.... that thing is huge!

Yeah they are a bit on the huge side
I think it is 90cm (3ft) long and 86cm (2 ft 10 inch) wide with the wings forward if they are folded back it is about 30 cm (1ft) smaller

gaz45 wrote: Wed May 16, 2018 11:23 am Stunning work there mate

Thank you Gaz

That's a huge model!

aur0ra145 wrote: Wed May 16, 2018 4:36 pm That's a huge model!

It is indeed
I have been looking around for other planes that are like it like the B-52 but it seems this is the largest 1/48 bomber as a injection molded kit
There are B-52 kits in 1/48 but those are vacuform kits and i can't make that work as well as a regular kit (as my miniart buildings have proven to me)

This bomber is looking awesome and huge! It is much bigger than my work area.

Love the way it's taking shape Mark - looks absolutely stunning.