Global Scale Modeller

I have never done a group build before, will see how I go. Will be a very quick build for me

Will be going with this in the Free French scheme that comes with the kit, some extra stowage and maybe an extra basket/seat on the rear as I have seen in a couple of photos.

20200902_193129 by Matthew Ashby, on Flickr

20200902_194454 by Matthew Ashby, on Flickr

If I get it done before time, maybe a 1/72 aircraft as well.

Looks like an interesting subject, I’ll pull up a chair

oh very nice... an interesting build so will watch with enthusiasm

Yep, this is a cool subject, looking forward to seeing the progress.

Nice bit of kit

always curious about Hobbyboss 1/35 kits, good luck with the build

Paul

Looks pretty cool - good luck!

I've never seen one of those before Looking forward to seeing how it all comes together - best of luck with the build

Tomcat64 wrote: Thu Sep 03, 2020 3:46 pm I've never seen one of those before Looking forward to seeing how it all comes together - best of luck with the build

Thanks everyone, will be getting a start on it tonight once a few reports for work are finished.

I'm not sure if it was only the French troops that used them or if other allied units did as well?
If anyone has any info let me know.

I like this kit alot!

Rugash wrote: Fri Sep 04, 2020 4:57 am

Tomcat64 wrote: Thu Sep 03, 2020 3:46 pm I've never seen one of those before Looking forward to seeing how it all comes together - best of luck with the build

Thanks everyone, will be getting a start on it tonight once a few reports for work are finished.

I'm not sure if it was only the French troops that used them or if other allied units did as well?
If anyone has any info let me know.

As far as I know only the french used these in Europe.

I found a thread by fly1ngdutchm4n from a while ago which I have found very helpful, especially in detailing the engine.

So I have made a little progress with detailing the engine as follows, with materials that I have at hand. Scale sizes? probably not spot on, but still looks ok.

1. Dipstick tube from styrene rod with a disk cut out of stretched sprue for the cap. Still have to make the handle which will be made out of 28 gauge brass wire.

2. Fuel line out of a piece of scrap wire bent to reach the fuel pump. I don't think I'll be running the fuel line any further from the pump to the tank.

3. Still have the spark plug wires to try, 28 gauge wire again. The problem is the distributor cap only has five plugs, so will have to sort that one out another way. The small tank on the LHS of the engine (power steering reservoir?) actually glues into #1 cylinder, so I might have to hide the front spark plug lead behind the tank. Not sure if they had assisted steering, just a guess at the moment.


20200904_223011 by Matthew Ashby, on Flickr

Then there's a coil lead and breather pipe to come.....
Also found the 270cu firing order as well...

nice start - do like an exposed engine but never been brave to add bits to one (someone has sent me a link to the engine manual for the M4 HST I am building... will have to consider if that will be upgraded)

robwuk wrote: Fri Sep 04, 2020 2:07 pm nice start - do like an exposed engine but never been brave to add bits to one (someone has sent me a link to the engine manual for the M4 HST I am building... will have to consider if that will be upgraded)

First time doing it myself, if I was sensible I would have tried it on one of my 1/25 cars first!
So far it has been worth it, no cursing, swearing or any other tantrums...

Working on the distributor at the moment, will take another photo when done

Rugash wrote: Fri Sep 04, 2020 2:17 pm

robwuk wrote: Fri Sep 04, 2020 2:07 pm nice start - do like an exposed engine but never been brave to add bits to one (someone has sent me a link to the engine manual for the M4 HST I am building... will have to consider if that will be upgraded)

First time doing it myself, if I was sensible I would have tried it on one of my 1/25 cars first!
So far it has been worth it, no cursing, swearing or any other tantrums...

Working on the distributor at the moment, will take another photo when done

Going well.....nice extra detailing

Have the engine detailing done, fair share of swearing during the process but has come up ok for my first attempt. One broken drill bit though, which of course it slipped and I stabbed my finger!

Have found otherwise that the dip stick is in the wrong place, should be in front of the distributor, but...... might move it yet

Have a bit of painting to do so I will prime this before I do the rest and then get it glued to the chassis.

20200906_211045 by Matthew Ashby, on Flickr

The engine is looking great. I feel for you, I just stuck an exacto knife in my finger.

nice work on the engine (not on stabbing yourself with a broken drill bit)

I followed suit on the M4 HST and added a little to the engine. I may look to see if there is more to add as, if I leave the grill doors open, you can actually see a fair bit of the powerplant

BigWall wrote: Sun Sep 06, 2020 6:18 pm The engine is looking great. I feel for you, I just stuck an exacto knife in my finger.

Done that more than a couple of times, also had a knife roll off the bench while I was reaching for something and stand at attention in my foot. That one leaked for a while

robwuk wrote: Sun Sep 06, 2020 6:49 pm nice work on the engine (not on stabbing yourself with a broken drill bit)

I followed suit on the M4 HST and added a little to the engine. I may look to see if there is more to add as, if I leave the grill doors open, you can actually see a fair bit of the powerplant

I'm going to add a couple of oil leaks and few other bits when I paint. Have a friend who has a lot off books he said I could borrow for doing my models. He has one on the CCKW trucks which looks great, but to be honest I probably won't finish it in time if I follow it.

Maybe the next one I'll go completely overboard with it

Rugash wrote: Sun Sep 06, 2020 12:53 pm Have the engine detailing done, fair share of swearing during the process but has come up ok for my first attempt. One broken drill bit though, which of course it slipped and I stabbed my finger!

Have found otherwise that the dip stick is in the wrong place, should be in front of the distributor, but...... might move it yet

Have a bit of painting to do so I will prime this before I do the rest and then get it glued to the chassis.

20200906_211045 by Matthew Ashby, on Flickr

nice detailing

Nice job.

Did the detailing info come with the instructions for the kit or did you have to research for that ?

Nice work on the engine and looking sweet

Toto wrote: Mon Sep 07, 2020 5:03 pm Nice job.

Did the detailing info come with the instructions for the kit or did you have to research for that ?

Thanks, no a friend has a large reference collection. He let me have a bit of a look through the CCKW book he has.

Hawkmoon wrote: Mon Sep 07, 2020 8:56 pm Nice work on the engine and looking sweet

Thanks mate, spark plug wires were hell

Really excellent job. The detailing takes it to a different level all together.

Cheers

Toto

Rugash wrote: Mon Sep 07, 2020 11:04 pm

Hawkmoon wrote: Mon Sep 07, 2020 8:56 pm Nice work on the engine and looking sweet

Thanks mate, spark plug wires were hell

spark plug leads, but the firing order too

Thank for the comments everyone

Have seen so many different engines, some with the dipstick tube behind the distributor and some in front...some engines painted grey and some painted in olive green (a GMC olive green gloss).

I'm done , will post a photo of the engine when I decide which damn colour I finally decide to use...

Some photos coming soon, assembling the chassis and other bits at the moment

Really nice work sprucing up that powerplant - the added details really take it to the next level!

As for the colour - it's your kit so paint it how you want I usually try to vary the shades to break up the monotony of an all green vehicle if I can - just to add a bit of interest.

Back again, been a bit busy with everything else this week but now have a bit of progress.

I have almost finish the main painting of the engine, still have some wear, a wash and some dust to add.
Some assembly of chassis and wheels done....getting there at least

I like how the wheels assemble to display the brake drum behind them. I have also left the exhaust off to paint and weather before gluing it on.

Also, I have painted the welch plugs brass and will add some green back to them to show some flaking paint.


20200913_165816 by Matthew Ashby, on Flickr

20200913_213822 by Matthew Ashby, on Flickr

20200913_213755 by Matthew Ashby, on Flickr

20200913_213804 by Matthew Ashby, on Flickr


20200913_215240 by Matthew Ashby, on Flickr

20200913_215258 by Matthew Ashby, on Flickr

Wow, that motor looks really good.

nice work on the engine... I am finishing the major components before starting the painting....

Thanks for the comments, really appreciated

I have tried doing the engine first and then I'll mask like fly1ngdutchm4n did in his build. See how it goes, hopefully get the chassis finished this week....depending on work again of course.

Enjoying being on here so far , will try and add a bit more of a description when I post as well.

Rugash wrote: Mon Sep 14, 2020 1:49 am Thanks for the comments, really appreciated

I have tried doing the engine first and then I'll mask like fly1ngdutchm4n did in his build. See how it goes, hopefully get the chassis finished this week....depending on work again of course.

Enjoying being on here so far , will try and add a bit more of a description when I post as well.

looking forward to it.

Really nice work on the engine - that's looks great

So, I've been missing for a couple of weeks but have been making some progress in that time as well. This could turn into more than one post so here goes or maybe just a long one.

Chassis -

I have continued with the assembly and in my usual way skipping steps to make painting etc easier...and harder for myself.
Decided to put the motor in and mask it up later, as the instructions indicate...

20200914_211044 by Matthew Ashby, on Flickr

20200914_211019 by Matthew Ashby, on Flickr


Cab and rear body -

Interior and PE on cab done, I did make up a accelerator pedal from a a Flak 30 foot rest (tan colour) as the instructions didn't show a part number for the pedal.....then several steps later noticed the accelerator pedal attached to sprue B, part 42.
Going to add a covering to the seats at some point, but will add the photos later.

Filled some pin marks and gaps, tried my hand at soldering the PE parts and have to say that I don't know why I hadn't tried it before as it works great. I even soldered a small loop between the toe hook and some chain for the winch.
Then a quick test fit to make sure everything lined up ok.

20200920_221528 by Matthew Ashby, on Flickr

20200920_221544 by Matthew Ashby, on Flickr

20200926_223913 by Matthew Ashby, on Flickr


20200926_224024 by Matthew Ashby, on Flickr

20200927_141854 by Matthew Ashby, on Flickr
20200927_141657 by Matthew Ashby, on Flickr
20200927_105227 by Matthew Ashby, on Flickr

20200927_142700 by Matthew Ashby, on Flickr

A bit more yet to come tonight, a few little details.

I have also made a change to the winch drum, made up some smaller cable from copper wire using five strands only to make a smaller diameter cable. The string cable supplied with the kit does tend to fray when painted.
The cable isn't perfect, but will look good enough I think when it's painted etc.
Filled the drum to allow me to make less cable that I would have to wrap around it.

Made a bed roll/stowage from the excess milliput left over.

Added some chains to the rear tailgate. Seems any builds that I could find on the net had it glued shut, so just to be different and add some more ammo boxes or personal effects.

20200928_185641 by Matthew Ashby, on Flickr

20200928_163521 by Matthew Ashby, on Flickr

20200928_163615 by Matthew Ashby, on Flickr


20200928_185633 by Matthew Ashby, on Flickr


20200928_205506 by Matthew Ashby, on Flickr

nice work on the build and cable. Am sure the string you have is the same on the M4 HST, it has frayed but can't see a great deal of it so will probably leave it..

Great detail work, chains and PE look brilliant

Looks great!

Very nice. I like the solder work on the PE

Really nice work - that PE is very tidy indeed!

Had a win with the winch cable, has worked out pretty good after snapping the tow hooks on the front bumper about a dozen times!
Had a bit of a play with the seats, tissue paper with pva glue and water mix.....stolen idea

Have started on the gun mount as well.
Hopefully some paint on soon.


20200929_110014 by Matthew Ashby, on Flickr

20200929_171909 by Matthew Ashby, on Flickr


20200928_232803 by Matthew Ashby, on Flickr

Keep up the good work borrowed or not doesn't matter

We've all borrowed some, or a lot, from someone. It's looking great!

Those tiny chains and wire look great!

Yep that's superb work and sharing ideas & techniques is what this place is all about

Not too much progress, a couple of other things getting in the way.

Gun is finished though, I thinned out the muzzle a little, drilled out the seat holes and everything else is from the box. PE was fiddly for the front sights with four wingnuts.

20201005_214009 by Matthew Ashby, on Flickr

excellent work with the gun sights.

Really nice work - as Digger already said those gun sights look superb, very delicate